在整個蠕動泵系統里面，軟管是常用的耗材，相應的在使用中也會出現許多的問題，今天雷弗總結了常見的幾個問題，希望能幫到大家。
In the entire peristaltic pump system, hoses are commonly used consumables, and there are also many problems that may arise during use. Today, Rafer summarized several common problems, hoping to help everyone.
問：軟管出現劃痕，甚至被劃破?？雌饋硐袷怯玫秳澠?。
Question: The hose has scratches or even been scratched. It looks like it was cut with a knife.
答：一般是由蠕動泵泵頭內的法蘭劃破的，主要是由于泵頭內的軟管較多，造成了堆積，泵頭內的法蘭在轉動的同時，邊緣部位會對軟管造成一定的劃傷。拆開后，還能在里面發現部分的軟管殘渣（法蘭邊在切割軟管遺留的）。
Answer: It is usually caused by the flange inside the peristaltic pump head being scratched, mainly due to the accumulation of many hoses inside the pump head. When the flange inside the pump head rotates, the edge area will cause certain scratches on the hoses. After disassembling, some hose residues can still be found inside (leftover from cutting the hose at the flange edge).
問：可是我泵頭內的軟管不多，為什么也會出現這種情況？
Q: But there aren't many hoses in my pump head, why does this happen?
答：請檢查軟管的轉卡，看是否裝卡合適。
Answer: Please check the transfer card of the hose to see if it is properly installed.
蠕動泵管安裝照片
Photo of peristaltic pump pipe installation
問：蠕動泵管安裝需要注意什么？
Q: What should I pay attention to when installing peristaltic pump pipes?
答：1、在安裝泵管之前，把泵放在平面上，否則在安裝泵管時會出現卡管現象。
Answer: 1. Before installing the pump pipe, place the pump on a flat surface, otherwise the pipe may get stuck during installation.
2、泵管要貼合泵頭安裝（盡量拉直），不能讓泵管在泵頭內的部分過長，因為這樣在泵運行時，泵法蘭會把軟管劃破。
2. The pump pipe should be installed close to the pump head (as straight as possible), and the part of the pump pipe inside the pump head should not be too long, as this will cause the pump flange to scratch the hose during pump operation.
3、泵管在使用前，要進行外部清潔處理，不得留有雜志，否則會影響泵管的回彈性以及輸送的精準。
3. Before use, the pump pipe should be cleaned externally without leaving any magazines, otherwise it will affect the resilience of the pump pipe and the accuracy of transportation.
4、確定泵頭的規格，不是所有的軟管都能安裝在同一種泵頭上面，否則將會出現竄管現象。
4. Determine the specifications of the pump head, not all hoses can be installed on the same type of pump head, otherwise there will be pipe leakage.
5、蠕動泵管需要用卡頭卡緊，避免出現竄動現象。
5. The peristaltic pump pipe needs to be tightened with a clamp to avoid any movement.
問：泵管無法回彈，管壁變薄過快，非正常磨損。
Question: The pump tube cannot rebound, the tube wall thins too quickly, and abnormal wear occurs.
答：這種現象通常是因為轉輪卡死、泵壓塊接觸泵型槽模具 一次性止血帶 保定水處理設備 一次性止血帶 保定空壓機 北京真空泵管的面和轉輪上有雜質、轉速過高造成造成的。泵頭的轉輪被卡死以后，蠕動泵的轉輪直接刮過蠕動泵管，就會增加軟管表面的摩擦造成軟管表面溫度升得很高和磨損軟管表面，過高的溫度也會使軟管失去彈性，極端情況下產生的溫度超過140度以上甚至?xí)斐绍浌苋芑冃巍?br />
Answer: This phenomenon is usually caused by the runner getting stuck, the pump pressure block contacting the surface of the pump pipe, impurities on the runner, and high rotational speed. After the rotating wheel of the pump head is stuck, the rotating wheel of the peristaltic pump directly scrapes over the peristaltic pump pipe, which increases the friction on the surface of the hose, causing the surface temperature of the hose to rise very high and wear the surface of the hose. Excessive temperature can also cause the hose to lose elasticity, and in extreme cases, temperatures exceeding 140 degrees Celsius can even cause the hose to melt and deform.
